Rectangle Wire Snap Rings

tax-term-featured-image

Arcon Ring’s rectangle wire snap rings are used for a variety of heavy-duty applications because of their support and stability, providing greater shoulder strength. Much like Eaton style snap rings provide a greater walled-shoulder for your application. Take advantage of Arcon’s short lead times to make sure you’ll have the right amount of wire rings right when you’ll need them.

Customizable Rectangle Wire Snap Ring Solutions

Arcon Ring offers customizable gap configurations of up to 10” in diameter for our open and closed rectangle wire rings. Arcon Ring offers customizable round wire rings. If you don’t see the exact configuration below to meet your needs, visit our Design Your Own Snap Ring section. Or if you found the part you’re looking for and only need a slight customization to make it work, contact us, we’d love to help you get right wire snap ring to fit your application.

Available Sizes: 0.188" to 1.00"

Standard Material: Carbon Spring Steel

Obtainable in: Bronze, Beryllium Copper, and Stainless Steel

drawing
PART NUMBER SHAFT RING GROOVE DIMENSIONS APPROX WT. LB/ 1000 PCS.
DIAMETER S DIAMETER WIDTH THICKNESS
Frac. inch Dec. inch Inside D Outside O W inches t inches A Width B Depth
TRC 813 3/16 0.188 0.176 0.226 0.025 0.015 0.017 0.0070 0.07
TRC 814 7/32 0.219 0.205 0.255 0.025 0.015 0.017 0.0070 0.08
TRC 815 1/4 0.250 0.230 0.300 0.035 0.025 0.028 0.0100 0.20
TRC 816 9/32 0.281 0.261 0.331 0.035 0.025 0.028 0.0100 0.23
TRC 817 5/16 0.312 0.290 0.370 0.040 0.025 0.028 0.0110 0.29
TRC 818 11/32 0.344 0.322 0.402 0.040 0.025 0.028 0.0110 0.32
TRC 819 3/8 0.375 0.351 0.431 0.040 0.025 0.028 0.0120 0.35
TRC 820 13/32 0.406 0.382 0.472 0.045 0.025 0.028 0.0120 0.42
TRC 821 7/16 0.438 0.412 0.502 0.045 0.025 0.028 0.0130 0.45
TRC 822 15/32 0.469 0.443 0.533 0.045 0.025 0.028 0.0130 0.48
TRC 823 1/2 0.500 0.474 0.570 0.048 0.035 0.039 0.0130 0.78
TRC 824 9/16 0.562 0.534 0.630 0.048 0.035 0.039 0.0140 0.90
TRC 825 19/32 0.594 0.565 0.685 0.060 0.035 0.039 0.0145 1.20
TRC 826 5/8 0.625 0.596 0.716 0.060 0.035 0.039 0.0145 1.30
TRC 827 11/16 0.688 0.656 0.776 0.060 0.042 0.046 0.0160 1.70
TRC 828 3/4 0.750 0.715 0.855 0.070 0.042 0.046 0.0175 2.10
TRC 829 13/16 0.812 0.776 0.916 0.070 0.042 0.046 0.0180 2.20
TRC 830 7/8 0.875 0.833 0.973 0.070 0.042 0.046 0.0210 2.30
TRC 831 15/16 0.938 0.896 1.058 0.081 0.042 0.046 0.0210 2.90
TRC 832 1 1.000 0.955 1.117 0.081 0.042 0.046 0.0225 3.00

Section

On request, listed sections may be coiled to meet any shaft or housing diameter requirements. eg. (1″ shaft dia.(s) × .045 × .025 section (w-t). 4″ limit on “O” diameter

Gap

(Trc type) butted to approximately 1/2 wire section dimension.

Tolerances

Tolerances on “D” dimensions are minus as follows:

3/16″ to 3/8″ sizes: 6%
13/32″ to 1″ sizes: 5%

Tolerances on “t” (thickness) dimension are as follows:

.015 to .025 sizes: ±5%
.035 to .042 sizes: ±4%