Plain Wire Snap Rings

plain wire ring specifications

Arcon Ring’s plain wire snap rings are primarily used within the drapery and vertical blind industry for their ease of installation.

Customizable Plain Wire Snap Ring Solutions

Arcon Ring offers customizable plain wire snap rings. If you don’t see the exact configuration below to meet your needs, visit our Design Your Own Snap Ring section.

Or if you found the part you’re looking for and only need a slight customization to make it work, contact us, we’d love to help you get right wire snap ring to fit your application.

Available In-Stock Sizes: .125" to .625"

Standard Material: Carbon Spring Steel

Standard Finish: Self Finish and oil

Diagram

PART NUMBERSHAFTRINGGROOVETc *Tg*APPLI-
CATOR
Diameter SThickness DiameterWidth
Frac. inchesDec. inchesTol. inchest inchesTol. inchesCC1G inchesTol. inchesW inchesTol. inches
1200-7 1/8 0.125   .032dia   0.31 0.34 0.08 +0.005 0.036   338 70 40
1200-11 5/32 0.156   .032sq   0.36 0.39 0.12 -0.000 0.036   434 63 41
1200-13 3/16 0.188   .036dia   0.45 0.49 0.13   0.040   603 139 42
1200-14 3/16 0.188   .032sq   0.40 0.44 0.14   0.036   532 84 43
1200-15 7/32 0.219 +0.005 .048sq   0.51 0.55 0.15   0.052   962 190 44
1200-15R 7/32 0.219 -0.015 .048dia   0.51 0.55 0.15   0.052   962 190 45
1200-17 7/32 0.219   .032sq   0.48 0.53 0.17   0.036 +0.003 600 104 46
1200-19 1/4 0.250   .040sq   0.48 0.54 0.20 +0.010 0.044 -.000 915 150 47
1200-21 1/4 0.250   .032sq ±.002 0.48 0.54 0.20 -0.005 0.036   723 125 47
1200-21R 1/4 0.250   .032dia   0.48 0.54 0.20   0.036   700 125 48
1200-22 17/64 0.266   .040sq   0.54 0.59 0.21   0.044   978 165 49
1200-23 9/32 0.281 +0.010 .048dia   0.56 0.61 0.22   0.052   1200 203 50
1200-25 5/16 0.313 -0.015 .040sq   0.57 0.63 0.26   0.044   1160 209 51
1200-34 3/8 0.375   .040sq   0.69 0.74 0.33   0.044   1400 153 51
1200-43 1/2 0.500   .056sq   0.87 0.94 0.44   0.060   2680 411 52
1200-52 9/16 0.563 -0.015 .064sq   1.03 1.10 0.50 +0.015 0.068 +0.004 3480 383 53A
1200-57 5/8 0.625   .064sq   1.12 1.20 0.56 -0.01 0.068 -.000 3880 452 54A

* It is recommended that the tolerance on Groove Diameter is restricted, where necessary, to maintain the minimum groove depth quoted when using shafts smaller than nominal.